Working Principle Of Industrial Pellet Burner
The biomass burner is a biomass semi-gasification automatic control burner that uses biomass particles, sawdust, wood powder, wood particles, rice husk particles, peanut shell particles, nut shells, fungus sticks and other agricultural and forestry solid wastes as fuel.
The biomass burner is mainly composed of a furnace combustion system, a primary oxygen distribution system, a secondary oxygen distribution system, a safety monitoring system, an ignition system and a feeding system. In addition, there are two different cooling models, air-cooled and water-cooled. Some high-end products also have remote control systems, which can automatically optimize combustion through big data, achieve more balanced and reasonable combustion, and achieve the purpose of energy saving!

Control Process And Mode
The overall work of Industrial Pellet Burner is divided into three stages:
1. Ignition stage: first, the feeding dragon of the burner is powered on to carry out the pre feeding action. After feeding, turn on the blower and the ignition rod to carry out the ignition action. The ignition time is about five minutes. Due to different materials and different ignition methods, the time length is different!
2. Feeding stage: after the ignition is successful, enter the fire feeding stage. The fire feeding is mainly composed of feeding and air supply. The feeding speed can be changed by the frequency converter or adjusted by the time interval mode, and the air supply size can be adjusted by the frequency converter!
3. Heating stage: the heating stage is a large fire. After the temperature reaches the set value, it enters the small fire stage, which can effectively avoid the waste of fuel. When the temperature is low, the fire will burn again! Repeat the switch back and forth! When the machine is no longer in use, it will enter the shutdown stage. In the shutdown stage, the blower will delay shutdown to blow out the fire in the furnace to avoid the formation of flue gas!
Features
1. High complete combustion efficiency: Boiling semi-gasification combustion and tangential swirling air distribution design make the fuel and combustion complete, and the combustion efficiency can reach more than 90%;
2. Complete and stable combustion: no tempering or de-firing occurs when the equipment operates in a micro-pressure state;
3. Wide range of heat load adjustment: the heat load of the burner can be quickly adjusted within the range of 30%-120% of the rated load, and the starting block is responsive;
4. The pollution-free environmental protection benefits are obvious: the renewable biomass energy is used as the fuel to realize the sustainable utilization of energy. Using low-temperature staged combustion technology, the emission of nitrogen oxides, sulfur dioxide and dust in flue gas is low, and it is an excellent substitute for coal stoves;
5. No discharge of tar, waste water and other wastes: using high-temperature gas direct combustion technology, tar is directly burned in the form of gas, which solves the technical problem of high tar content in biomass gasification and avoids the water quality caused by washing tar. Secondary pollution;
6. Simple operation and convenient maintenance: automatic feeding, wind removal, simple operation, small workload, only one person on duty;
7. Low investment and low operating cost: The biomass combustion structure is reasonably designed, and the transformation cost is low when used in various boilers.
Technical Parameter
|
Burner Specifications |
Overall Dimensions |
Machine Weight |
Flamethrower Diameter |
Number of Igniters |
Burning Materials/H |
Motor |
Fan |
|
200,000 kcal |
65*58*110cm |
125KG |
16CM |
1 piece |
10-356KG |
250W |
240W |
|
400,000 kcal |
65*58*110cm |
135KG |
22CM |
1 piece |
15-50KG |
250W |
240W*2 |
|
600,000 kcal |
65*58*110cm |
150KG |
27CM |
2 pieces |
20-90KG |
250W |
240W+330W |
|
800,000 kcal |
88*78*137cm |
200KG |
27CM |
2 pieces |
30-120KG |
250W |
240W+550W |
|
1 million kcal |
110*88*163cm |
240KG |
27CM |
2 pieces |
40-150KG |
250W |
240W+330W+550W |
|
1.2 million kcal |
110*88*163cm |
280KG |
27CM |
2 pieces |
50-200KG |
250W |
240W+550W*2 |
|
1.6 million kcal |
110*88*163cm |
320KG |
33CM |
2 pieces |
60-250KG |
250W |
330W*2+550W*2 |
Installation Method

Schematic Diagram

Application Range
1. Applied to various boilers: such as garment factories, catering industries, etc.,
2. Applied to powder spray drying production line,
3. Applied to zinc-aluminum alloy die-casting industry
4. Applied to various thermal energy equipment, such as road construction, asphalt heating heat conduction furnace, food oven, air conditioner heater, snow sweeper, garbage incinerator, hot air generator and various general boilers.

Special Precautions
1. The fuel must use 6-8mm pure sawdust biomass pellets, do not use pellet fuel with too many pellets and magazines. Prevent the iron sword from entering the material box when feeding! If the equipment is damaged due to poor fuel or iron objects entering the tank, it will not be covered by the warranty;
2. It is best to use negative pressure in the furnace of boilers or other equipment, and it is strictly forbidden to have excessive positive pressure. If the positive pressure is too large, an induced draft device should be installed;
3. The cover of the material box must be closed during operation to prevent waste. When the furnace is shut down, the material isolation valve must be closed to prevent tempering;
4. If there is material blocking and jamming, (usually caused by too long particles), use a wooden stick to poke it down. Never use iron wire or steel bar to prevent it from being involved in the screw and causing damage to the screw;
5. Burner cleaning: After the burner works for a period of time, coking will occur near the burner. If this phenomenon occurs, it will seriously affect the operation of the burner. In severe cases, the burner will be damaged! Therefore, regular inspection and decoking are required. (It is recommended to check every 3 to 7 days).
6. Decoking method: remove the burner from the equipment used, and tap the coke block with a wooden stick or iron stick from the burner to make it separate from the gasification chamber. (Be careful not to damage the gasification chamber and the fire passage when decoking) Coking has a lot to do with fuel, it is recommended to use pure wood fuel)
General Troubleshooting
1. Black smoke is emitted from the chimney - reason: too much material is fed, and the furnace cannot digest it. Treatment method: stop feeding for a few minutes, observe the normal exhaust of the chimney, and then start the normal feeding; reduce the feeding speed, and the chimney has no black smoke emission;
2. There is spark rebound at the furnace mouth - reason: the slag accumulation in the equipment system is not smooth, or the burner nozzle is blocked by carbon deposits. Treatment method: clean and dredge the slag in the heat transfer system of the production line or clean the slag in the burner nozzle. Generally, under the condition of 8 hours/working day, use the equipment furnace or pipeline heat transfer system to clean and dredge the slag accumulated once in 3 months.
Maintenance
1. Burner cleaning: After the burner works for a week, check whether there is coking near the burner. If this phenomenon occurs, it will seriously affect the operation of the burner. In severe cases, it will cause damage to the burner! Therefore, regular inspection and decoking are required. Check once every 3-7 days of operation, and close the slag cleaning port after cleaning and dredging the accumulated slag every day.
Decoking method: Remove the burner from the equipment used, and tap the coke block with a wooden or iron rod from the burner to make it separate from the gasification chamber. (Note: Do not damage the gasification chamber and the fire passage when decoking.) Coking has a lot to do with fuel. It is recommended that the soil content of the fuel should be 1%-3%. If the impurity content is too large, it will cause a lot of Coking will reduce the service life of the equipment.
2. Regularly check whether the running parts of the equipment are loose, add lubricating oil regularly to the bearing position, and check at least once a week.
Our Guarantees And Services
Pre-Sale Service:
- Guide customers to choose the appropriate equipment model.
- Send engineering and technical personnel to the production site in time to plan the site for customers, design reasonable processes and solutions.
- We can design and manufacture products according to the special needs of customers to meet the different needs of investors
On Sale Service:
- Strict inspection of products before leaving the factory
- Ships according to contract
After-sale Service:
- The main warranty period of the equipment sold by our company is one year (except for the failure or damage caused by human factors, fuel factors or irresistible natural phenomena, and vulnerable parts are not covered by the warranty: fuel injectors, pump heads, photosensitive eyes, etc.).
- If the equipment failure is caused by human factors, the cost will be charged according to the factory price.
- After receiving the warranty notice, reply within 2 hours. 24 hours technical guidance to solve problems.
About Odifei Company

Zhengzhou Odifei Machinery Equipment Co.Ltd id founded in 2004, which is a specialized enterprise dedicated to R & D and production of the tire recycling plant, tire pyrolysis plant, distillation plant, waste engine oil refining plant, tire crusher, plastic crusher, tire cutter machine, rubber powder plant, tyre shredder machine, plastic shredder, Heavy oil burner, Industrial Oil Burner, diesel burner, biomass pellet burners, pulverized coal burner, biomass burner, biomass pellet burner,biomass straw burner, wood pellet burner, Industrial Pellet Burner, 300,000 Kcal Waste Oil Burners, Bucket elevator, vertical vibrating feeder, belt conveyor, scraper conveyor, screw conveyor, chain conveyor, etc.. our company by reputation first, service first, customer first is an objective and take integrity as life. All for customer's satisfaction efforts, all for the company's long term healthy development efforts. We solemnly promise that we will develop us with good quality and credible after sale service! We sincerely welcome you to our company and give us suggestions and directions!!!
FAQ
Q: Are you a factory or a trading company? When we use a burner, can we use it to burn other raw materials?
A: We are a factory, established in 2007, specializing in the production of heavy oil fuel engines, diesel burners, biomass pellet burners, biomass burners and other burners. If you need to burn other raw materials, please select the corresponding burner.
Q: Can heavy oil burners use light diesel as fuel?
Answer: Yes, heavy oil burners can use light diesel as fuel; but light diesel burners should try not to use heavy oil as fuel, which will easily block the nozzle.
Q: How to choose the right burner?
A: According to the required heat, fuel, boiler size and other parameters.
Q: How is the Industrial Pellet Burner installation?
A: For the installation of the burner, we will provide you with the wiring diagram and technical support. Generally, you can do it yourself; but if you really need our technicians, we will send them to your workplace as needed.
Q: What about spare parts?
A: We always provide spare parts at cost price and provide you with a spare parts list when you buy the machine.
Q: Will you test the Industrial Pellet Burner before delivery?
A: Yes, we will test each Industrial Pellet Burner before shipment and send you the working video. You can also contact us before delivery.
Q: Can I be an agent of the burner in our area?
A: Thank you for your trust. Please contact us for preliminary verification: First, whether there is already a local agent for the burner. Second, whether the agency conditions are met.

If you are interesting in Industrial Pellet Burner, please feel free contact us in 24 hours!
Welcome you visiting our factory!!!
Hot Tags: industrial pellet burner, China industrial pellet burner manufacturers, suppliers, factory











