Instructions For Use Of Methanol Gas Burner
Methanol burner is a device that integrates methanol supply, atomization, air supply, ignition, flame detection and operation adjustment control, etc., and is installed on the same cabinet to realize automatic control of the combustion process.
Working Principle
Using the classic ejector combustion principle, combined with air, automatic control, combustion and other principles, the methanol fuel is truly fully burned (customers with higher requirements can choose a silicon carbide tube); overcome the need for secondary filtered crude methanol , waste methanol and other fuels with more impurities, prevent blockage and pump damage, and completely get rid of high-pressure pump pressure atomization.

Features
1. High thermal efficiency: It can adapt to pressure fluctuations and adjust the primary air distribution by itself (that is, if the gas pressure is large, the primary air is more inhaled; the gas pressure is small, the primary air is inhaled). The alcohol-based fuel special burner has sufficient combustion and high thermal efficiency;
2. High safety: when the boiler starts up, the burner will first light a small fire. When the small fire burns normally and stably, the alcohol-based burner will be used. The main gas valve will be opened by the automatic control system, and the fuel can enter the boiler for normal combustion without deflagration. ;
3. Strong fuel adaptability: This kind of burner can be used for natural gas, liquefied petroleum gas, coal gas, liquefied petroleum gas mixture and other types of gas and fuel only by replacing a few parts.
4. Good atomization of burning methanol, low energy consumption and low noise
5. The alcohol/gas coordination is good, the flame is stable, the combustion efficiency is high, and the environmental pollution is small.
6. Reliable installation, automatic control
Technical Parameter
|
Model |
ODF-30 |
ODF-40 |
ODF-60 |
ODF-80 |
|
Fuel |
Methanol, light diesel oil, kerosene and other liquid fuels (heavy oil and waste oil fuels require heavy oil burners) |
|||
|
Air Pressure(MPa) |
0.3 |
|
|
|
|
Size (mm) |
630*650*380 |
1000*740*430 |
1030*740*430 |
1270*850*500 |
|
Protection class(IP) |
45(The protection level can be increased according to the order requirements) |
|||
|
Air volume adjustment method |
Manual damper adjustment |
Automatic damper adjustment |
||
Application Range
1. Applicable to all kinds of boilers: such as garment factories, restaurants, hotels, bath centers, etc.
2. Applied to powder spray drying production line,
3. Applied in zinc-aluminum alloy die-casting industry
4. It is used in various thermal energy equipment, such as road construction, asphalt heating heat conduction furnace, food oven, air conditioner heater, snow blower, garbage incinerator, hot air generator and various general boilers.
5. Suitable for waste tire cracking equipment, waste oil distillation equipment, refining equipment, waste plastic pyrolysis equipment, etc.

Maintenance
The burner does not require special maintenance, but the following should always be done:
1. Cut off the power supply, remove the electric eye, and wipe it with a clean dry cloth.
2. Remove the fuel injector and carefully clean it with gasoline or trichloroethylene. Note that only wood and plastic tools can be used, not metal tools. After 2000 hours of normal operation, the fuel injector should be replaced.
3. Carefully clean the oil filter on the fuel injector.
4. Remove the cyclone, remove the soot on the cyclone and in the combustion head, and make the air flow channel unobstructed.
5. Carefully clean the electrodes, scrape off the ash and carbon deposits, and correct the position and distance between the two electrodes.
6. Carefully clean the filter in the oil pump.
7. Clean the oil filter and the oil tank. If the filter screen is found to be damaged, it should be replaced in time. If there are many deposits in the oil tank, it should be cleaned.
8. If necessary, clean the flue of the boiler and chimney.
Note: The casing of the burner cannot be cleaned with organic solvents (such as: alcohol, acetone, banana water), but only with a mixture of water and detergent. Qiku should always pay attention to the oil level in the oil tank, and it is not allowed to lower to the specified position, so as not to damage the oil pump.
Installation Preparation
1. Installation
(1) Preparation before installation
(a) Check that the bacon (cross-sectional area and height) conforms to the boiler manufacturer's requirements and local standards.
(b) The voltage and frequency of the power supply must meet the requirements of the burner.
(c) The system and size must comply with the requirements of this manual. The gate and accessories of the oil circuit system should be considered, and the oil suction pipe and return pipe should be checked for air tightness.
Check, no leakage is allowed under 125 times the maximum working pressure. (d) Check whether the accessories supplied with the burner are available.
(e) Calculate the relevant data according to the pressure of the boiler furnace, the operation curve of the burner in Figure 5, the pressure set by the burner oil pump and the specifications of the oil nozzle: calibration
Whether the output of the nuclear burner can meet the requirements for the heat supply of the boiler, if it cannot meet the requirements, the nozzles of other specifications should be replaced, but it should be noted that the fuel injection volume should match the burner, and it is not allowed to exceed the maximum and combustion requirements of the boiler. The maximum allowable value of the burner cannot be less than the minimum output of the burner. Otherwise it cannot be used. (2) Installation
(a) Put the mounting flange on the air supply pipe, install the asbestos gasket between the boiler mounting plate and the mounting flange, and then tighten the bolts. The boiler plate, asbestos pad, and installation flange should be sealed, and ventilation is not allowed to prevent the high-temperature fine air from being exposed during the operation of the boiler, which will damage the boiler and connect the boiler according to the requirements of the boiler.
Extend into the combustion chamber, and then fix the flange on the air supply pipe with the bolts on the installation fasine.
(b) According to the oil circuit system diagram, use an oil-resistant hose to connect the oil suction port of the oil pump to the oil suction pipe, and connect the oil return port to the oil return pipe. Connect the power cord and related circuits according to the circuit diagram
Our Guarantees And Services
Pre-Sale Service:
- Guide customers to choose the appropriate equipment model.
- Send engineering and technical personnel to the production site in time to plan the site for customers, design reasonable processes and solutions.
- We can design and manufacture products according to the special needs of customers to meet the different needs of investors
On sale service:
- Strict inspection of products before leaving the factory
- Ships according to contract
After-sale service:
- The main warranty period of the equipment sold by our company is one year (except for the failure or damage caused by human factors, fuel factors or irresistible natural phenomena, and vulnerable parts are not covered by the warranty: fuel injectors, pump heads, photosensitive eyes, etc.).
- If the equipment failure is caused by human factors, the cost will be charged according to the factory price.
- After receiving the warranty notice, reply within 2 hours. 24 hours technical guidance to solve problems.
About Odifei Company

Zhengzhou Odifei Machinery Equipment Co.Ltd id founded in 2004, which is a specialized enterprise dedicated to R & D and production of the tire recycling plant, tire pyrolysis plant, distillation plant, waste engine oil refining plant, tire crusher, plastic crusher, tire cutter machine, rubber powder plant, tyre shredder machine, plastic shredder, Heavy oil burner, Industrial Oil Burner, diesel burner, Natural Gas Burners, pulverized coal burner, biomass burner, Natural Gas Burner,Methanol Gas Burner, 300,000 Kcal Waste Oil Burners, Bucket elevator, vertical vibrating feeder, belt conveyor, scraper conveyor, screw conveyor, chain conveyor, etc.. our company by reputation first, service first, customer first is an objective and take integrity as life. All for customer's satisfaction efforts, all for the company's long term healthy development efforts. We solemnly promise that we will develop us with good quality and credible after sale service! We sincerely welcome you to our company and give us suggestions and directions!!!
FAQ
Q: Are you a factory or a trading company? When we use a burner, can we use it to burn other raw materials?
A: We are a factory, established in 2007, specializing in the production of heavy oil fuel engines, diesel burners, Natural Gas Burners, biomass burners and other burners. If you need to burn other raw materials, please select the corresponding burner.
Q: Can heavy oil burners use light diesel as fuel?
Answer: Yes, heavy oil burners can use light diesel as fuel; but light diesel burners should try not to use heavy oil as fuel, which will easily block the nozzle.
Q: How to choose the right burner?
A: According to the required heat, fuel, boiler size and other parameters.
Q: How is the machine installation?
A: For the installation of the burner, we will provide you with the wiring diagram and technical support. Generally, you can do it yourself; but if you really need our technicians, we will send them to your workplace as needed.
Q: What about spare parts?
A: We always provide spare parts at cost price and provide you with a spare parts list when you buy the machine.
Q: Will you test the Methanol Gas Burner before delivery?
A: Yes, we will test each Methanol Gas Burner before shipment and send you the working video. You can also contact us before delivery.
Q: Can I be an agent of the burner in our area?
A: Thank you for your trust. Please contact us for preliminary verification: First, whether there is already a local agent for the burner. Second, whether the agency conditions are met.

If you are interesting in Methanol Gas Burner, please feel free contact us in 24 hours!
Welcome you visiting our factory!!!
Hot Tags: methanol gas burner, China methanol gas burner manufacturers, suppliers, factory











