Home-Products - Continuous Pyrolysis Machine-

Content

Continuous Rubber Powder Pyrolysis Equipment

Continuous Rubber Powder Pyrolysis Equipment

The Continuous Rubber Powder Pyrolysis Equipment is to convert various types of waste (such as rubber, plastic, and biomass) into valuable products like pyrolysis oil, carbon black, and gas.

PRODUCT INTRODUCTION

PRODUCT INTRODUCTION

Continuous Rubber Powder Pyrolysis Equipment

Continuous Rubber Powder Pyrolysis Equipment is an industrial environmental protection equipment used to convert waste rubber (usually crushed rubber powder) into fuel oil, carbon black, and combustible gas through high-temperature oxygen-free heating.

Continuous Rubber Powder Pyrolysis Equipment

Process Flow of Continuous Rubber Powder Pyrolysis Equipment

Continuous Rubber Powder Pyrolysis Equipment is a chemical pyrolysis technology. The specific process is as follows: 

Fully Continuous Pyrolysis Plant

Step 1:Feeding system

The rubber powder is transported to the continuous pyrolysis plant by means of large inclined conveyors, silos, motorized ball valves, and sealed conveyors.

Step 2:pyrolysis process

In the pyrolysis reactor, the rubber powder runs along the inner wall of the reactor through the spiral scraper.
The whole pyrolysis reactor is in a closed and oxygen-free state, and heated by indirect heating, producing oil and gas, carbon black, and non-condensable gas. The continuous pyrolysis reactor of ODIFI adopts a three-way design, which reduces the floor space of the reactor under the circumstance of ensuring that the rubber powder can be fully pyrolysed; in addition, the indirect heating prolongs the service life of the reactor.

Step 3:cooling process

The oil gas generated in the pyrolysis reactor first passes through an oil gas separation system, then an oil gas purifier, and finally is sent to a cartridge condensation system (with circulating cooling water as the cooling medium) for cooling and storage in oil tanks.

Step 4:Non-condensable gas recovery treatment

In addition to oil and gas during the entire pyrolysis process, a portion of non-condensable gas is generated. The non-condensable gas passes through two safety water seals and through a gas spray gun, which can continue to heat the pyrolysis reactor, thus reducing operating costs.

Step 5:Flue gas treatment 

The flue gas generated by rubber powder pyrolysis and non-condensable gas combustion will enter the flue gas treatment equipment for treatment. Generally, the flue gas system is equipped with two sets of spray dust removal. It should be noted that the specific environmental protection device configuration plan needs to be configured according to the environmental protection emission standards implemented by the customer's local area.

Step 6:Discharge the carbon black

There is a slag outlet at the rear end of the pyrolysis reactor. The carbon black is transported to the cooling conveying device through a high-temperature sealed conveyor and enters the carbon black storage bin through three cooling spiral devices. Then it can be centralized for packaging.

Running Video  of the Continuous Rubber Powder Pyrolysis Equipment

In this video, you can see clearly how the continuous rubber powder pyrolysis equipment works. 

Final pyrolysis products and uses

 The first number every rubber powder buyer asks for is oil yield, and the second is what the residue is worth. Below is the split for tire-derived rubber powder (2.8–10 mm granules, steel wire removed, moisture under 1 %) in our continuous line. These ranges come from commissioning records; your exact figure depends on mesh size and rubber content, and we confirm it with a lab pyrolysis test on your sample before signing.

Output    t moves the number
Pyrolysis oil 42 % – 48% Higher mesh (finer powder) and higher rubber content push it up; natural rubber share matters more than SBR.
Carbon black 30 % – 35 % Finer powder gives cleaner black. Ash above 10 % indicates poor wire/fiber removal upstream.
Combustible gas 7 % – 10 % Recycled to the burner - this is what makes the line self-heating after start-up.
Loss/moisture 2 % – 5 % Wet powder wastes heat evaporating water before pyrolysis starts.

Why rubber powder outperforms whole tyres: the steel wire and fiber are already removed, and the partsize is uniform, so the reactor heats evenly and the oil and gas condense consistently. Condensate fluctuates because bead wire and tread rubber pyrolyse at different rates. This is why buyers who already own a granulation line get a faster payback on the pyrolysis unit than buyers feeding whole tyres.

Advantages of Continuous Rubber Powder Pyrolysis Equipment

Core Features and Advantages of Continuous Rubber Powder Pyrolysis Equipment  are as follows:

High degree of environmental protection

The whole pyrolysis process of the fully continuous pyrolysis plant adopts sealed feeding and slag discharge. The whole production process is in a highly sealed state, and the production workshop environment is clean and hygienic.

High output

The output of a single continuous pyrolysis plant device can reach a processing capacity of about 50 tons or more, while the daily processing capacity of a single intermittent pyrolysis device is only 15 tons.

Low operating costs

The continuous pyrolysis plant reactor is designed with an anti-coking device, and there is no coking during the pyrolysis process; the PLC controls the heating point to make the continuous pyrolysis plant reactor evenly heated, extending the service life of the reactor; the combustible and non-condensable gas is recycled and reused to heat the reactor, reducing the cost of fuel use; circulating water is used for cooling to reduce water resource waste;

Technical parameters of Continuous Rubber Powder Pyrolysis Equipment

Model JZLXLY-20 JZLXLY-30 JZLXLY-50
Capacity 20tons per day 30tons per day 50tons per day
operating system Continuous type
Pyrolysis reactor

15CrmoR;304tainless steel;it can be customized

Heating type Indirect heating
Heating fuel Fuel, gas, etc.
Cooling Type cooling water
Workers Required 1-2 workers

Continuous VS batch

 A fully continuous pyrolysis plant can process about 50 tons per day, but it may not be suitable for you. If you are not sure whether it is suitable for you, the picture can help you more:

Fully Continuous Pyrolysis Plant

Success case

Continuous Rubber Powder Pyrolysis Equipment

patent

The reactor three-way design/anti-coking system is patented; certificates can be provided upon inquiry. 

Fully Continuous Pyrolysis Plant

F&Q

1. What raw materials can the equipment process besides rubber powder?

Its primary design feedstock is tire-derived rubber powder (2.8–10 mm, wire removed). The same reactor platform also runs waste plastics and oil sludge, but each material needs configuration changes - plastics require the anti-coking system and a dechlorination stage when PVC is present; oil sludge requires the decoking scraper. The quotation is built for one primary material, and alternates are validated on a sample before we confirm them.

2. How many days can it run continuously, and what does maintenance involve?

Up to 60 days of continuous operation between stops, verified on running sites. Each planned stop takes 2–3 days: reactor inspection, scraper and seal replacement, condenser tube cleaning. Unplanned stops are rare once feeding quality is under control - most are caused by oversize or wire-contaminated powder, which is why we specify the mesh range.

3. Can the machine actually reach its rated daily capacity?

Yes, when the feedstock meets the specification in the quotation - the rated figures assume dry powder within the stated mesh range. If your powder carries moisture above 3 % or fiber contamination, actual throughput drops and we will tell you at the design stage rather than after installation. We can arrange a live view of a running site's daily production log so you can verify capacity before ordering.

4. How long from equipment arrival to first oil?

Installation and commissioning take 20–25 days with our engineers on site, including operator training. First oil typically comes 12 days into commissioning, and full-rate production follows once the feeding line is tuned. Site civil works and the cooling water system must be finished before our team arrives - we send the foundation drawing at contract signing.

5. Does an engineer come to our site for installation?

Yes. One to two engineers supervise unloading, installation, commissioning and a full operator training cycle (normally 【填:天数】 days). Their flights, accommodation and a supervision fee are quoted transparently in the contract - there is no after-the-fact markup, and the training covers daily startup, shutdown, maintenance intervals and troubleshooting.

6. What certificates do you provide for import and environmental approval?

 CE,ISO9001. For local environmental approval, we supply the flue-gas treatment configuration and expected emission parameters so your consultant can file with the authorities - the exact spray-tower setup is matched to your local emission standard, which is why we ask for it at the design stage.

 

 

Hot Tags: continuous rubber powder pyrolysis equipment, China continuous rubber powder pyrolysis equipment manufacturers, suppliers, factory

SEND INQUIRY

SEND INQUIRY